Impact on cost accuracy and profitability from implementing product configuration system – A case-study Anna Myrodia and Katrin Kristjansdottir and Lars Hvam Abstract. 1 This article aims at analyzing the impacts from function PCS enables improved decision making in the early implementing a product configuration system (PCS) on company’s phases of engineering and sales processes [6]. Furthermore, the profitability and improved cost estimations in the sales phase. system can be used as a tool that allows the salesperson to offer Companies that have implemented PCSs have achieved substantial custom-tailored products within the boundaries of standard product benefits in terms of being more in control of their product architectures, thereby giving companies the opportunity to be more assortment, making the right decisions in the sales phase and in control of their product assortment [7]. As the various benefits increasing sales of optimal products. Those benefits should have a are described from implementing a PCS, it can be concluded that direct impact on improved profitability in terms of increased those benefits will have direct impact on the company’s contribution ratios and more accurate cost estimations used to profitability in terms of increased contribution ratios and more determine the price in the budgetary quotations. As the literature accurate cost estimations in the sales phase. However the link describes, there are various benefits from implementing a PCS, between implementing a PCS and its effects on the company’s however the effects on the company’s profitability have not been profitability has not received much attention from researchers, even discussed in detail. This study analyzes the impact from though it is one of the most critical factors during the planning implementing a PCS on the accuracy of calculations in the phase of such a system. Ergo this article focuses on assessing the quotations and the impact on the relative contribution ratios of impact of the implementation of a PCS on companies’ profitability products. For that reason, a configure-to-order (CTO) by analysing the accuracy of the cost calculations in the sales phase manufacturing company has been investigated. A longitudinal study is performed where both the accuracy of the cost calculations and the profitability of the products in terms of their contribution and the profitability is analyzed before and after the ratios. Based on this, the following propositions are developed: implementation of a PCS. The comparison reveals that increased profitability and accuracy of the cost estimation in the sales phase Proposition 1 The accuracy of the cost calculations in the can be achieved from implementing a PCS. quotations is increased by the implementation of a PCS. Proposition 2 The contribution ratio of products is increased when 1 INTRODUCTION they are included in a PCS. In today’s business environment companies are forced to offer customized solutions without compromising delivery time, quality Aiming to investigate these effects, a longitudinal case study and cost [1]. In order to respond to those challenges mass was performed. In 2009, an analysis of the product’s profitability customization strategies have received increasing attention over the and accuracy of the cost calculations in the quotations generated in years, both from practitioners and researchers. Mass customization the sales phase was conducted. The results from that analysis refers to the ability to make customized products and services that indicated that the performance of the sales processes could be fit every customer through flexibility and integration at cost similar improved by the implementation of a PCS. That recommendation to mass-produced products [2]. Utilizing product configuration was adopted by the company; hence a PCS was developed and systems (PCSs) is one of the key success factors in order to achieve implemented in 2011. Three years later, the same analysis was the benefits from the mass customization approach [2][3]. performed in order to determine the impacts on the company’s PCSs are used to support design activities throughout the profitability that could be related to the implementation of the PCS. customization process, where a set of components along with their The comparison of the results before and after the implementation connections are pre-defined and where constrains are used to of the configurator is assessed and discussed in relevance to the prevent infeasible configurations [4]. This is one of the reasons propositions. why configurations systems are considereded to be among the most successful applications of artificial intelligence [5]. This paper is structured in 5 sections. In section 2 the relevant Once implemented, the PCS usually supports the sales and literature will be analyzed in terms of PCSs and the benefits that engineering processes in various dimensions, which can lead to can be achieved from implementing such a system. In section 3 a numerous benefits such as; shorter lead-times, more on-time case study will be presented where the influence on company’s deliveries, improved quality of the product specifications, less profitability and the accuracy of the cost calculations from rework and increased customer satisfaction. Besides, its supportive implementing a PCS will be analyzed. Then, in section 4 the conclusions from the case study are discussed. Finally, in section 5 1 discussion about the findings of this research work and future Engineering Management Department, Technical University of research are presented. Denmark, Denmark Email: annamyr@dtu.dk, katkr@dtu.dk, lahv@dtu.dk 11 Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria 2 LITERATURE REVIEW improvement for the companies, as it has been measured 75% to 99.9% reduction of quotation lead time. In this section the theoretical background of the present research is Another case study performed by Hvam [13] discusses and reported. In order to find the relevant publications a literature quantifies the impact from the implementation of a PCS in the review has been performed in the research area of PCSs. electronics’ industry. The main benefits from the use of Forza and Salvador have performed extensive research in this configuration tools are considerably lower costs for specification field. The authors present a case-study of an CTO manufacturing processes and production. The reason for that is that when company, that identifies the benefits of the implementation of a specifications are generated in the PCSs, the actual working time product configuration tool [8]. The benefits discussed are reduction for preparing offers and production instructions tends to be near of delivery time, improved customers’ relationships and zero. The benefits in that case-study are quantified and show that elimination of errors in Bill-Of-Material (BOM). They quantified the fixed production costs have been reduced by 50%. the impact that the use of a configuration tool has on lead time, as Additionally, the variable production costs have been reduced by reduction of manned activities in the tendering process (tendering 30%. On top of that quality has been improved, and is realized as a lead-time from 5–6 days to one day). In addition to that, the errors reduction from 30% to less than 2% in the number of assembly in the products' BOM, misunderstandings between salespersons errors, as well as delivery time has been reduced from 11 – 41 days and customers are eliminated, while at the same time the level of to one day. After-sales services and installation are also positively correctness of product information has been increased, reaching affected by the configurator. For instance, the time for replacing a almost 100%. In a related study [7], the authors present a case- battery has been reduced from 5–6 hours to 20–30 minutes. study of a manufacturer, who's production strategy is based on Hvam et al. [14] performed another case measuring the impact customers' orders. After the implementation of a product of implementing a PCS in the ordering process of a CTO configurator, one of the benefits identified is reduction to almost manufacturer. It is noted that only a 0.45% of the specification zero of the errors in the configurations released by the sales office, process time is value adding. As a result the non-value adding time in addition to savings in man-hours. There have also been noted spent on making the specifications can be reduced by the use of a significant benefits in production, including manufacturing and configurator. By automating the process fewer errors occur, the assembly processes, due to the fact that by using the configuration productivity of employees is improved and the quality of tool correct information are received in the production. information and documents is increased. That is due to both Furthermore, there has been an increase in technical productivity, reducing the standard deviation of the duration of the processes and both regarding product documentation release and design activities. avoiding errors in quotations. To this end, the benefits of using a PCS in the sales process are Similarly to the previous, another case-study is performed by further investigated [9]. One of the main advantages discussed is Hvam et al. [15] in an ETO provider of cement plants. The benefits that the configuration tool describes the possible configurations of of the implementation of an IT-supported product configuration in the product in a way that they are simple and understandable by the the quotation process of complex products are aligned to those customer. In that way, it can be ensured that there are no discussed above. In detail, a reduction in lead time from 15-25 days contradicting requirements, no missing specifications and that to one-two days for the generation of quotations is noted. An product configurations produced are valid. Moreover, since the increase in the quality of quotes as it is made possible to optimize configurator deals with real time information, it helps reducing the cement plants satisfying better the customer’s needs, and dialogue time between salespersons and customers. Finally, it is making less errors in the specifications made in the PCS. highlighted that any kind of miscommunication between the Resources consumption for making quotations is reduced in the salespersons and the customers is eliminated and possible errors engineering department from five man-weeks to one to two man- are reduced. The reason for that is a possible source of errors in the days. quotations due to the sales personnel lack of technical knowledge. Aldanondo et al. [16] identify the main benefits as the reduction The use of a product configurator and its effect on product of cost and cycle time for highly customizable products. That is quality is discussed by Trentin et al. [10]. The authors performed a due to the fact that without the support of PCSs iterative survey in order to verify the relationship between the use of a procedures occur in sales and design processes. These activities configurator and the quality of products. The results show a result in generating longer cycle time and increasing costs. positive effect on product quality by using a product configurator. Slater [17] analyses the benefits of a web-based configurator in Haug et al. [11] discuss possible development strategies for CTO environments. By using a PCS the company is able to offer product configurator and evaluate the concluding benefits. the right product from the very beginning to each customer. The Advantages identified are, firstly, the convenience of evaluating PCS assists the sales personnel to have an overview of the valid information included in the configurator software before configurations and, therefore, avoid mistakes in the communication implementation and ease of altering implemented product with the customers. This results in eliminating re-works on the information. Facilitating the communication between product customers’ order. The same knowledge embedded in the experts and configurator software experts is essential in order to configurator is used to provide unique manufacturing instructions build a configuration tool. This results in minimizing use of and to make the rules for the correct configuration accessible to the resources on documentation work and handovers of information, engineers. and rapid implementation of gathered information. The benefits Gronalt et al. [18] outline the benefits of the implementation of realized are both fewer chances of misunderstandings and errors, a PCS, such as personalized customer support, representation of and faster processes. Haug et al. [12] performed another study in knowledge and distributed reusability of consolidated product 14 ETO companies, where the impact of implementing a PCS on configurations. To this end, Hong et al. [19] discusses the use of a lead times is quantified. The results indicate significant configurator so as to reduce the information and attributes used to configure a product variant in One-of-a-kind production (OKP). Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors 12 Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria Fleischanderl et al. [20] provide empirical evidence showing was not using a PCS, and in 2014, 4 years after the implementation that a configurator supporting the product development and of the configurator. The reason for selecting that specific period is production process can reduce the cost of the product’s life cycle up to ensure that the PCS has been fully integrated into the business to 60%. processes of the company, therefore increasing the validity of the The implementation of a PCS in the sales and marketing process comparison. The data for this research was gathered from has direct effects, such as number of errors, pricing, accuracy, time company’s internal databases and was verified with experts from and cost to reworks, time to validate, reduce order cycle time, the company. improve salespersons' morale, improve customers' satisfaction [21]. Empirical evidence from a built-to-order manufacturer claim benefits such as increase on customer satisfaction, lower costs and 3.1 Background higher productivity. In addition to these, an increase in the The company analysed in this case study is a Nordic company in technical accuracy of orders entering manufacturing processes is the building industry that operates worldwide. In the year 2014 the noted, which also leads to cost and errors’ reduction [22]. company had around 100 employees and yearly turnover of Tenhiala and Ketokivi [23] performed a survey in make-to- approximately 15 million Euro. On average the company has order (MTO) manufacturing companies and found support to the around 50 projects per year where the average turnover per project hypothesis that the use of product configurator software in MTO is approximately 300.000 Euro. The company manufactures pre- production processes is positively associated with product made structural elements for buildings. The product portfolio conformance. Additional findings indicate that in general the use of consists mainly of six products; A, B, C, D, E and F. The first four configuration management practices in MTO production processes products have standard product architecture that can be adjusted to is positively associated with product conformance and delivery the customers’ needs. Products of type E denote to all the non- performance, among custom assemblers and producers. standardized solutions and products of type F relate to additional Another problem that product configurators should focus on, features or to the parts that can be added to the standard solutions. according to Blecker et al. [5], is the customer perspective. They In 2009 the process of making budgetary quotation and the claim that designers of configurators mainly concentrate on the accuracy of the cost estimation were analysed, which revealed the back-end technical aspects. By process simplification and company’s performance of accurate cost estimations could be personalization the wrong interpretation of the customer improved. The analysis also revealed that the company’s procedure requirements by the supplier can be avoided. PCSs can therefore be of using Excel sheets to make the calculations of estimating the beneficial both for the sales and engineering processes. prices resulted in many errors that could be traced to human Tiihonen et al. [24] conduct a survey in Finish manufacturers mistakes. Based on this analysis the company decided to invest with modular-based products. Their findings indicate that in 150.000 Euro to develop a PCS to improve the processes of extreme cases 80% of the sales specifications are either incomplete generating budgetary quotations. The PCS used at the company is a or inconsistent. At the same time, less than 20% of the total commercial PCS, which builds on constrains propagation. In working time in the order processing is used for value-adding addition to that, the company also made process improvements and work. By implementing PCSs there is a reduction to the number of changes in the product assortment that aimed to increase errors related to quality and to quality costs. Moreover, the sales' standardisation. The implementation of the PCS also ensured that specification produced by the configurator can be directly used as the salespersons are going to provide the customers with valid an input for production, as it will not contain errors. Finally, the configurations from the standard product architecture. configuration can assist the representation of products and product The development of the PCS took place in the period 2009 – families that are often differentiated in different market areas, and 2010, and in beginning of 2011 the company had developed a PCS also the transfer of up-to-date product configuration knowledge to able to handle most of the budgetary quotations. Only products of the sales units and to enforce its proper use. type E, which are categorized as non-standard solutions, have not Summarizing the findings from the literature review, it can be been included in the system. However, due to insufficient change seen that the implementation of a PCS provides various benefits to management, not all employees were willing to change their work the manufacturers, in terms of resources’ reduction, reduction of procedures and therefore they still used Excel sheets to make the lead time, better communication with customers and product cost calculations for making the budgetary offers. quality. However, there is a lack of empirical evidence on In this case study the impact from implementing the PCS on the quantifying the impact of the use of a product configuration tool on company’s ability to make accurate price estimations for the improved profitability and more accurate cost estimation. This budgetary offers and the company’s profitability will be assessed. work contributes to that fact, by providing a longitudinal case The analyses were done both before implementing the system and study, comparing the economic performance of the products and for the period of its utilization over, the past 4 years (2011-2014). the accuracy of quotations before and 4 years after the Thereafter the accuracy of the calculations made by using the implementation of a PCS in a CTO manufacturer. Excel sheets and the PCS will be compared. 3 CASE STUDY 3.2 Analysis of the Company’s Performance In order to examine the propositions a case study is performed. The Before and After Implementation of purpose of this case study is to illustrate the difference between Product Configuration System cost estimation accuracy and product profitability, when using a In order to compare the performance before implementing the PCS PCS and without one. Therefore, a longitudinal case study is (2009) and after the implementation (2011-2014), contribution performed, by making similar analysis in 2009, when the company margins (CM) and contribution ratio (CR) were calculated for each 13 Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria project that had been carried out at the company within the 3.2.1 Analysis of Cost Structure and Deviations timeframe of this research. Those calculations where both based on the estimations of the budgetary quotations and both the real cost In this section the company’s cost structure and the deviations in and sales prices calculated after each project had been closed. CM the estimated and actual values with regards to the main cost and CR are calculated as follows [25]: elements is analysed. The purpose of that analysis is to identify whether cost estimations have been improved after the CM = Sales Price – Cost Price (1) implementation of the PCS by analysing the main cost elements. CR=CM / Sales Price (2) The cost elements that are included in the analysis represent the direct cost of making the product, which covers the expenses Finally, the deviation in the CR is then calculated as actual CR related to materials, salaries, subcontractors and for the minus the estimated CR. construction site, e.g. renting machines. In 2009 a cost analysis was performed in order to assess the DEV = CRactual - CRestimated (3) economic benefit by implementing a PCS. This benefit is highly associated to the reduction of deviations in the cost estimation, as If the real cost of the project is higher than the estimated cost, it the application of a PCS would thereby improve the budgetary will result in negative deviation of the CR. Respectively, if the real quotations. In Figure 1 the results from the analysis are shown for cost of the project is less than the estimated it will result in positive the deviation in the CM for the cost calculations of the main cost deviation in the CR. The data for the analysis was extracted from elements. the company’s internal database and verified with specialist at the company. The cost prices of the projects were calculated as the sum of the costs for expenses on construction site, subcontractors, materials and salaries. The projects included in the comparison are from 2009, when only the Excel sheets were used to calculate the cost, until 2014. For the period 2011-2014 the cost calculations are either done in the PCS or by using Excel sheets. In Table 1 the main results from the analysis are listed. Table 1. Overall analysis of the PCS contribution in terms of CR before implementation (2009) and after implementation (2011-2014) Performance indicators Year ◊ □ ○ ◊◊ 2009 -1.5% 5.4% 14.6% 25.0% Figure 1. Deviations in cost estimations for the projects 2009 2011 -3.6% 7.7% 28.5% 25.5% distributed between the main cost elements 2012 -0.7% 4.9% 8.9% 27.6% 2013 -2.4% 4.9% 9.5% 28.8% The figure above shows great deviations and irregularities in the 2014 -1.1% 3.9% 2.2% 28.6% pattern, which indicate that only a few projects were realized at the ◊ Average difference in CR □ Average absolute deviation in CR ○ same cost as calculated. This means that the salespersons have Percentages of projects with greater deviation than 10% ◊◊ Average CR per project estimated significantly lower costs for the projects than the actual ones, as the deviations are mainly negative. That means that the The analysis shows that the average CR has steadily increased sales persons underestimated the cost of the project. That refers to from 25.0% in 2009 to 28.6% in 2014. However, the overall all different cost categories, as they all deviate towards the same company’s goal is to have projects with CR of 30%. direction (positive or negative). Based on this it can be concluded The deviations in the CR also show positive improvements as that the accuracy of the calculations for the budgetary proposals the average deviations have been reduced from -1.5% in 2009 to - were inadequate in 2009. 1.1% in 2014. Regarding the absolute value of the CR, when In order to see whether the situation has been improved at the analyzed, the deviations showed reduction from 5.4% to 3.9%. It company since implementing the PCS, a similar analysis was should also be noted that the percentages of projects with greater repeated in 2014, three years after implementing the PCS. The deviation than 10% have been significantly reduced from 14.6% in results from the analysis are shown in Figure 2. 2009 to 2.2% in 2014, as the calculations of the absolute values in the CR indicate. However in 2011, which was the first year when the PCS was utilized, the deviations in the CR increased considerably. This increased in deviations can be traced to the fact that the system had not been fully tested before implementation and the users of the system were lacking training. But as the users became more experienced in using the system and errors had been fixed, the PCS started providing valuable results. This analysis indicates that the calculations are now more precise than before the implementation of the PCS and the company is moving closer to the targeted CR, which is 30%. Figure 2. Deviations in cost estimations for the projects in 2014 distributed between the main cost elements Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors 14 Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria subcontractors. Under certain circumstances, time can be limited As illustrated in the above figure, when comparing the deviations and the company’s employees might get closer to a deadline for a in CMs of the projects from 2014, it can be clearly noted that there project and the construction team cannot finish on time. Then it are far less fluctuations in the cost calculations than in 2009. might be necessary to outsource the work to subcontractors to Beside a few projects, the majority of them have rather low finish on time and not delay the project, as that will also cause deviations from the calculated budget. By comparing the results higher additional cost. from Figures 1 and 2, it can be realised that the accuracy of cost It can be concluded from the above analysis that the main estimations has been improved since implementing the PCS. This reasons for the deviations in the cost calculations were not due to is also supported by the fact that the deviations from 2009 for all inconsistences of the PCS. Late changes from the customers, the cost elements are not towards the same direction, meaning that unforeseen circumstances and outsourcing are some of the main in 2009 the deviations were negative in their overwhelming factors reported by the project managers of the company, which majority. when occur, cause deviations in the cost calculations. The costs in 2014 are closer to the baseline; nevertheless, three large negative spikes for the subcontractor category can clearly be seen, on the same projects with the positive spikes for the salaries. 3.3 Comparison of Budgetary Proposals Made From an interview with a specialist at the company the reason for in Excel and PCS the large deviations in these three projects was due to the fact that In 2011 the PCS was first launched in the company. However, it the construction work was outsourced to subcontractors. This has not been accepted by all sales representatives therefore some of explains why the subcontractor category reveals large deviation them were still using Excel sheets for the calculations. The main and at the same time there is a positive deviation in the salary reason for that is the lack of change management initiatives, which category, as the work was outsourced and therefore salaries to own resulted in some employees resisting to use the PCS and therefore employees could be reduced for the projects. sticking to their old work habits. In this chapter the yearly turnover, In the project where there is a large positive deviation in the CR of the projects and the deviations of the CR will be analysed in material category. The explanation given was that from the time terms of whether they were generated by the Excel sheets or the by the proposal was given out and until it was finished it took several the PCS. years and in the meantime a new steel structure was developed and The turnover generated by projects sold through the PCS has implemented, which was much cheaper than the old structure. The been steadily increasing since 2011. In the year 2013 the point was large positive deviations in the cost estimations that were noticed reached, where slightly more proposals were generated by the use in the 2014 analysis have therefore been reasonably explained. In of the PCS. Figure 3 shows the yearly turnover for the proposals the next section a more general explanation for the deviation is made in Excel and by use of the PCS. provided. 3.2.2 Reasons for the deviations In order to gain a better understanding of the deviations in the cost estimations, a deeper analysis is performed, with the aim of clarifying why these deviations are still occurring at the company. The most significant deviations in the projects 2014 have been explained above, however in this section additional factors that influence the deviations will be further analysed. The company aims to provide the customers with high quality service therefore if a customer wants to make changes to the specifications later in the process, the company will strive to adjust the solution to satisfy the customer’s wishes. When such changes occur, the additional cost is added manually to the total price. This makes the actual cost of the project deviate from the initially Figure 3. Comparison of turnover generated for proposals made in calculated cost, but does not affect the profitability of the project. Excel and by use of the PCS Furthermore, the cost at the construction site is difficult to estimate since there are frequently unforeseen factors which have As can be seen from the above figure, in 2011 and 2012, the to be dealt with, such as difficulties to get the machines at the projects handled by the salespersons through the Excel sheets building side. That can result in increasing the time that the contributed more to the turnover of the company; even though the machines have to be rented and creating additional expenses due to PCS has already been implemented in that period. This can be salaries of subcontractors, which were not taken into account in the explained, firstly, by the reluctance that some of the salespersons original calculation of the estimated cost. However, this threat showed towards including the new PCS in their working processes, could be reduced if technicians would examine the construction as they still used Excel for the cost calculation and quotation site in order to make more realistic estimations of the cost. generation. Additional, the period 2011-2012 was the initial However, it worth mentioning that the highest peaks in the introduction of the PCS at the company. However, the PCS did not deviations of the cost calculations in 2014 are not caused by errors include all products at that point of time; therefore its utilization in the quotations, or additional costs due to unforeseen factors at was by definition limited. As a consequence, during the trial period the construction site but mainly because of the outsourcing work to the turnover contributed by the projects handled in Excel is higher than the one from the PCS, but this fact was significantly changed 15 Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria in the following 2 years. So, in the period 2013-2014, when the company managed to take greater advantage of the PCS, and its utilization was strongly established, the turnover of the projects worked out by using the PCS outnumbered the ones worked out in Excel. 3.3.1 Sales Representatives and CR The company’s goal is that all projects should have a CR of 30%. An analysis of the overall performance of the company, (section 3.2) showed how the CR has been increasing since 2009. However, in order to confirm that this can be traced to the implementation of the PCS, a comparison of the CR for the budgetary proposal made by using the PCS and Excel is performed. In Figure 4, the actual CR is illustrated for the proposals made by use of the PCS and Excel. Figure 5. Comparison of deviations in CR for sale persons using Excel and PCS As it can be seen from the above figure, the salespersons using the PCS have less deviation in their CR than the ones using Excel, with the exception of the year 2011 which was the first year the system was used in the company. Moreover, in 2012 and 2014 the deviations of the quotations made by the PCS are positive and close to 0. The analysis of the performance of the salespersons using Excel and PCS therefore indicates that the PCS affects positively the accuracy of the cost estimation as well as the CR. Summarizing the results from this section, it can be seen that both the CR and the accuracy of estimations are improved by the utilization of the PCS. To this end, it can be concluded that the both propositions are supported by the results of the case study. Figure 4. Comparison of CR for salespersons using Excel and PCS From this it can be concluded that salespersons using the PCS 3.4 Future Initiatives contribute a higher CR, with an exception in the year 2012 where it In order to improve the company’s performance several factors was slightly lower. Furthermore, it can be seen that the gap have been identified that could reduce even further the deviations between the CR is increasing between the salespersons using Excel in the CR and increase the profitability of the company. The and the PCS. In 2014 the average CR was 28.6%, where sale company intends to implement a check list in the end of each persons using the PCS had average CR 30.1% while sale persons configuration in order to ensure that all the required information is using Excel had 23.8%. In other words, the salespersons using the both gathered in the sales phase and up-to-date. By implementing PCS have managed to achieve the goal of 30%. the check list, it is expected that errors made in the sales process However as previously mentioned the products of type E, which will be reduced even further. Furthermore, the company is planning are the non-standard products, are not included in the PCS to enhance a higher degree of standardization in their product therefore in order to make the price estimation Excel sheets are range, as well as move towards modular based product always used. Even though those products are not included in the architecture. Finally, the company has decided to invest 140.000 calculations for the proposals made in Excel, when they were taken Euro in further development of the PCS, in order to include more into account they only affected the CR for the proposals made in products and have greater benefits from its utilization. Excel by 0.2%. Therefore it can be concluded that the reason for lower CR cannot be traced to the special orders. Another important factor is to compare the deviations in the CR 4 CONCLUSIONS between the proposals made in Excel and PCS. The results are The scope of this case study is to quantify the impact of illustrated in Figure 5. implementing a PCS on product profitability and accuracy of cost estimation. The research results in significant improvements in both the CR of products sold through the PCS and the accuracy of quotations. These results confirm the propositions made in this paper. In detail, an improved performance of the margins of the products is recorded, as well as a reduction in the deviation of quotations. The comparison in the quotations’ deviation is made between the same products, sold in 2009, before the company implemented the configurator, and in 2014, when the sales process Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors 16 Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria was supported by the PCS. Moreover, there is a comparison [6] L. Zhang, ‘Product configuration: a review of the state-of-the-art between the CR of products being sold with and without the use of and future research’, International Journal of Production Research, 52, 6381–6398, (2014). the configurator for the period 2011 to 2014, when the PCS has [7] C. Forza and F. Salvador, ‘Managing for variety in the order been implemented and used to its full potential. Both comparisons acquisition and fulfilment process: The contribution of product lead to the same conclusion, that the contribution of the PCS is configuration systems’, International Journal of Production noteworthy, as the performance of the products included in the Economics, 76, 87–98, (2002). PCS is improved. Additionally, the deviations between the initial [8] C. Forza and F. Salvador, ‘Product configuration and inter-firm co-ordination: an innovative solution from a small manufacturing quotation provided to the customer by the PCS and the actual cost enterprise’, Computers in Industry, 49, 37–46, (2002). of each project are eliminated. Since the data used in the PCS is [9] C. Forza and F. Salvador, ‘Application support to product variety updated and all possible solutions are validated before making an management’, International Journal of Production Research, 46, offer, the quotation includes fewer errors and more accurate price 817–836, (2008). estimation, when it is compared to the quotations of the products [10] A. Trentin, E. Perin, and C. Forza, ‘Product configurator impact on product quality’, International Journal of Production not included in the PCS. Economics, 135, 850–859, (2012). [11] A. Haug, L. Hvam, and N. H. Mortensen, ‘Definition and evaluation of product configurator development strategies’, 5 DISCUSSION AND FUTURE RESEARCH Computers in Industry, 63, 471–481, (2012). [12] A. Haug, L. Hvam, and N. H. Mortensen, ‘The impact of product This work focuses on the benefits of implementing a PCS in a configurators on lead times in engineering-oriented companies’, configure-to-order manufacturing company. The benefits widely Artificial Intelligence for Engineering Design, Analysis and discussed in the existing literature are directed towards customer Manufacturing, 25, 197–206, (2011). satisfaction, cost reduction due to a better use of resources and [13] L. Hvam, ‘Mass Customization in the electronics industry’, elimination of errors, and improved product quality. The empirical International Journal of Mass Customisation, 1(04), 410 – 426, (2006). evidence provided in this research is based on a single case study. [14] L. Hvam, M. Bonev, B. Denkena, J. Schürmeyer, and B. Dengler, However, the company is considered to be a typical example and ‘Optimizing the order processing of customized products using highly representative in the configure-to-order industry. product configuration’, Production Engineering, 5, 595–604, This research is the first step in exploring the impact of a (2011). configurator on product’s profitability. Hence, similar cases also [15] L. Hvam, M. Malis, B. Hansen, and J. Riis, ‘Reengineering of the quotation process: application of knowledge based systems’, need to be examined, in order to compare the profitability between Business Process Management Journal, 10, 200–213, (2004). projects going through the PCS and outside of it. By examining [16] M. Aldanondo, ‘Expert configurator for concurrent engineering: more cases, a deeper understanding can be gained and a more Cameleon software and model’, Journal of Intelligent detailed explanation of the correlation between configuration tools Manufacturing, 11, 127 – 134, (2000). and product profitability can be provided. [17] P. J. P. Slater, ‘Pconfig: a Web-based configuration tool for Configure-To-Order products’, Knowledge-Based Systems, 12, In this paper empirical evidence is provided by only one case 223–230, (1999). study. Yet, the impact registered in this company indicates that [18] M. Gronalt, M. Posset, and T. Benna, ‘Standardized there could be significant impacts from implementing a PCS, Configuration in the Domain of Hinterland Container Terminals’, which have not been discussed in the literature previously. Series on Business Informatics and Application Systems Therefore, this requires further research and additional case-studies Innovative Processes and Products for Mass Customization, 3, 105-120, (2007). in order to justify the underlying correlation between PCS and [19] G. Hong, D. Xue, and Y. Tu, ‘Rapid identification of the optimal profitability increase. product configuration and its parameters based on customer- centric product modeling for one-of-a-kind production’ Computers in Industry, 61, 270-279, (2010). REFERENCES [20] G. Fleischanderl, G. E. Friedrich, A. Haselböck, H. Schreiner and M. Stumptner, ‘Configuring large systems using generative constraint satisfaction’, IEEE Intelligent Systems,13, 59-68, [1] C. Forza and F. Salvador, ‘Managing for variety in the order (1998). acquisition and fulfilment process: The contribution of product [21] J. Heatley, R. Agarwal and M. Tanniru, ‘An evaluation of an configuration systems’, International Journal of Production innovative information technology—the case of Carrier Economics, 76, 87–98, (2002). EXPERT’, The Journal of Strategic Information Systems, 4, 255- [2] B. J. Pine II, Mass Customization: The New Frontier in Business 277, (1995). Competition, Harvard Business School Press, Boston, 1993. [22] V. E. Barker, D. E. O’Connor, J. Bachant, and E. Soloway, [3] F. T. Piller and P. Blazek, Core capabilities of sustainable mass ‘Expert systems for configuration at Digital: XCON and beyond’, customization,107-120, Knowledgebased Configuration–From Communications of the ACM, 32, 298–318, (1989). Research to Business Cases, Morgan Kaufmann Publishers, [23] A. Tenhiälä and M. Ketokivi, ‘Order Management in the Waltham, 2014. Customization Responsiveness Squeeze*’, Decision Sciences, 43, [4] A. Felfernig, G. E. Friedrich, and D. Jannach, ‘UML as domain (2012). specific language for the construction of knowledge-based [24] J. Tiihonen and T. Soininen, ‘State of the practice in product configuration system’, International Journal of Software configuration–a survey of 10 cases in the finnish industry’, Engineering and Knowledge Engineering, 10, 449-469, (2000). Knowledge intensive CAD, 1, 95-114, (1996). [5] T. Blecker, N. Abdelkafi, G. Kreuter and G. Friedrich, ‘Product [25] P. W. Farris, N. T. Bendle, P. E. Pfeifer and D. J. Reibstein, The configuration systems: State-of-the-art, conceptualization and Marketing Accountability - Marketing Metrics: The Definitive extensions’ in: A.B. Hamadou, F. Gargouri, M. Jmail (eds.): Guide to Measuring Marketing Performance, Pearson Génie logiciel & Intelligence artificielle, Eigth Maghrebian Education,Upper Saddle River, New Jersey, 2010. Conference on Software Engineering and Artificial Intelligencev (MCSEAI), Sousse, Tunesia, 2004, 25–36, (2004). 17 Juha Tiihonen, Andreas Falkner, and Tomas Axling, Editors Proceedings of the 17th International Configuration Workshop September 10-11, 2015, Vienna, Austria