Geometric Modeling and Optimized Design of an Hydraulic System for Concrete Batching Plant Lucia Cocilovo1, Antonio Fichera2, Giuseppe Di Lorenzo2 1 Department of Electric, Electronics and Computer Engineering, University of Catania, Catania (Italy) 2 Euromecc S.r.l., Misterbianco (CT) Abstract - The present paper describes the geometric turned over 180°. The inside height of the open top 40″ modeling and design and the feasibility study of an innovative container is about 2 m. The minimum closed length of the hydraulic system that would allows a mobile batching plant to telescopic cylinder needs to be of 1 m to suit the container improve the safety, to increase the reliability and to reduce the transport truck dimension. Assuming a rails inclination of 70° concrete working process time. In particular, the present paper from the horizontal plane, the stroke of the cylinder must be of outlines the dynamic behavior of a telescopic hydraulic cylinder 7 m to permit the skip to travel from the bottom to the top in order to replace the current lift system (skip). Mechanical along the rails. The table below presents the technical features theory, principles of hydraulics, geometric modelling and design, of a suitable telescopic cylinder: using cad software, were used in developing the model of the telescopic cylinder. Using the spreadsheet software Excel it was possible to compare dynamic movements of some types of Table. 1. Technical features of telescopic cylinder actuators. An approach to a hydraulic batching plant lift systems is presented, where the results are compared with those obtained Technical features Values and units from the existing skip. Load capacity 3000 kg Keywords - Hydraulic cylinder; Batching plant; 3D modeling; Operating pressure 160 [bar] Reliability; Safety. Stroke speed 34 [m/min] Stroke length 7000 [mm] I. INTRODUCTION Closed length 1000 [mm] In a mobile batching plant, the skip is a type of loading Open length 7000 [mm] system that provides the requirement of small dimensions in the construction site. The skip is a conveyor lift system Load capacity (Retraction) 1000 [kg] operated by ropes. Given the issues related to: the operation of Mounting configuration Pivot mounts the lifting device, the reliability of limit switch sensors, the Mounting condition: incline angle 70° probability of breaking the ropes and other issues involving Environmental condition Dusty the use of the skip, it was considered essential to investigate the behaviour of a hydraulic system. Due to the plant’s System operating temperature -10°C < T < +40°C requirement of small dimensions in the transport configuration, suitable for container – transport trucks, the idea is to replace the skip system with a single-acting II. A BRIEF OVERVIEW OF THE HYDRAULIC SYSTEM telescopic hydraulic system. The main elements of the hydraulic system are: 1. 3 phase 4 pole asynchronous electric motor (15 kW) 1450 rpm 2. Internal gear pump (160 bar) 3. Pressure gauge and shut-off valve 4. 4/3- way directional control valve 5. Throttle adjustable valve 6. Pressure relief valve (safety valve) 7. Cooler 8. Exhaust filter 9. Intake filter 10. Oil reservoir tank 11. Pipes Fig. 1. Transport configuration of mobile batching plant. 12. Single- acting telescopic cylinder (4 stages) The schematically circuit of single-acting telescopic cylinder In this configuration, the skip rails and the main frame are is shown in figure 3. Copyright held by the author(s). 37 When the control valve is moved in the opposite direction, connecting the chamber of the cylinder with the tank, oil is forced to pass by the throttle valve (5), that it regulates the speed of descent. The telescopic cylinder returns to its initial retracted configuration, thanks to the gravity, because the hopper discharges the inert into the mixer and it remains only the empty hopper of 1000 kg of weight. The pressure relief valve(6) is placed immediately after the pump. The spring is adjusted to the maximum working pressure, in such a way that in case of overpressures, the fluid is discharged into the reservoir tank. One of the most important components of the hydraulic drive system is the telescopic hydraulic cylinder, that is an actuator which gets its power from pressurized hydraulic fluid (oil, in this case) and it is used to convert fluid power in mechanical motion. A single-acting cylinder transfers a hydraulic force in one direction only and it must be retracted by gravity (in this specific case). Fig. 2. Operative configuration of mobile batching plant. III. THE TELESCOPIC HYDRAULIC CYLINDER Telescopic cylinder is a special design of hydraulic cylinder which provide an exceptionally long output travel from a very compact retracted length. It consists of nested multiple cylinders called sleeves, which slide inside each other. A telescopic cylinder is used when a long stroke length and short retracted length are required. It normally extends from the largest stage to the smallest. Fig. 4. Functionality of telescopic cylinder. Fig. 3. Schematically circuit of single-acting telescopic cylinder. This means the largest stage, with all the smaller stages nested inside it, will move first and complete its stroke before A pump, driven by an electrical motor, takes oil from that the next stage begins to move. This procedure will reservoir and the fluid passes through a filter (9), before to continue for each stage until the smallest diameter stage enter in the circuit. (plunger) will be fully extended. Conversely, when retracting, When the 4/3 control valve (4) is in its neutral position, the the smallest-diameter stage will retract fully before the next telescopic cylinder (11) is hydraulically locked and the pump stage starts to move. This continues until all stages are nested (2) is unloaded back to the tank (10). Oil filters (8-9), situated back in the main. During the initial extension, the cylinder in the return line to the tank and before the pump, trap solid extends at the slowest speed and with most force. A smaller particles while allowing fluid to pass trough [1, 2]. diameter stage will extend next, the cylinder extends faster When the 4/3 way valve is actuated, the discharged line is with less force. under pressure because the pump must overcome the force of The cylinder load capacity is calculated considering the load (3000 kg) to be moved [3]. The oil, passing from the 4/3 smallest sleeve diameter in the assembly. way valve, feeds the ascent of the cylinder. Gravity return type single-acting cylinder is where the cylinder extends to lift a weight [4] against the force of gravity 38 by applying oil pressure at the blank end. To retract the From the above-mentioned equations it appears clear that cylinder, the pressure is simply removed from the piston by the parameters of the simplified model refer to the properties connecting the pressure port to the tank. of rigid body, kinematic and geometric data; moreover, many of these parameters are changing in time. A consequent Table. 2. Technical features of telescopic cylinder difficulty in obtaining an accurate valuation derives; the valuation of the single force component identified by the eq N° of stages of telescopic 10 9 6 5 (2) was not possible as during the experimental tests the cylinder stages stages stages stages displacement signal was not recorded. However, it was Closed length [mm] 910 1000 1550 1528 looking for identifying the static component of the resistance Open length [mm] 7055 8000 7800 7073 forces by referring to the time intervals where the signals in pressure were constant or slowly changed. As these intervals Working max pressure [bar] 200 160 200 200 concerns, a regression of the external force signal was Stroke length [mm] 6315 7000 6250 5620 fulfilled as experimentally measured with respect to theoretic Load Capacity [ton] 6.5 - 28 3 34 - 63 10 - 45 signal which was calculated by considering the pressures in Stroke speed [m/min] 30 30 30 30 the chambers of the cylinder ( ), using different Amount of oil [l] 149 - 77.5 80 models. Φ minimum stage [mm] 68 30 80 88 I Modello: ; da cui: ; (3) Φ maximum stage [mm] 265 220 192 190 II Modello: ; da cui: (4) Total weight [kg] 391 - 215 253 The first model assumes the presence of a resistance force IV. NUMERICAL MODEL OF HYDRAULIC CYLINDER as costant and indipendent from the force levels exerted by the The continuity equation about oil, which after introduction cylinder. into the cylinder end runs down the opposite site, can be so The second model assumes instead that the resistance formulated [5]: forces are proportional to the applied force. The dynamic behaviour of the system was simulated assuming the theoretic force as input variable and the force (1) exerted by the cylinder , experimentally measured, as signal With: in output. The same problem of a missing recording of the - i=1, 2, ..., 10 stages displacement signal occured again. Therefore the choice to realize an empiric model trying to minimize the number of - , useful thrust surfaces in the cylinder [m2] freedom degrees was taken. After repeated numerical simulations,it was noticed that a model with a unique pole and - , opening and closing speed of the extensions zero was the most effective: only with three degrees of - , volume of fluid entering / leaving the cylinder [m3] freedom (the static benefit and the position of the pole and zero), it is indeed able to interpolate effectively the - , pressures in the cylinder inlet / outlet chamber [Pa] experimental data, always provided an index of correlation r2 - Compressing equivalent modulus (thus considering superior to 0.85 Analysis of telescopic cylinder dynamic the fluid, the air contained in it, etc) movements Supposing that the oil mass in the hydraulic cylinder can By comparing cylinder features it was selected the 10- be omitted and act as a rigid body, Newton's second law of stages cylinder to examine in depth its dynamic movements. motion finds out that: Table. 3. Stages diameter of 10-stages cylinder N° of stages Diameter [mm] (2) 1 68 With: 2 88 - a acceleration of the extensions 3 107 - x extension direction 4 126 5 145 - B coefficiente di smorzamento viscoso [Ns/m] 6 165 - coulomb friction force [N] 7 187 - external force [N] 8 210 9 236 - m equivalent mass of moving parts [kg] 10 265 - force that includes all the resistive forces [N] 39 Table. 4. Areas, volumes and speeds of each stage. N° of stages Sleeve cross section Sleeve volume Speed sleeve area [mm2] [mm3] [mm/s] 1 3632 0.002 3590 2 6082 0.004 2144 3 8992 0.006 1450 4 12469 0.008 1046 5 16513 0.011 790 Fig. 6. Space-time chart 10-stage cylinder. 6 21383 0.014 610 From the analysis of the above performance chart the 7 27465 0.019 475 research was focused on finding a more linear extension of the 8 34636 0.024 376 cylinder, reducing the difference between the initial and the 9 43744 0.030 298 final extension speed. 10 55155 0.038 236 The figure 7 was analyzed the space-time chart trend of the ropes lifting system (skip). The next step was to find a Total 0.161 cylinder with a similar space-time chart. An Excel table was created to find relationships between different variables related to cylinder movements. It was used to calculate each stage velocities and then the results were analyzed creating different graphs. The extension speed shows a slowly increasing trend as a function of the extension time, while, when the cylinder extends to the last stage (the plunger- Ø minimum stage), it reaches the highest speed. Fig. 7. Space-time chart rope lifting. Using SolidWorks ver. 2016, it was created a 3D design of the 10-stages telescopic cylinder, in order to analyze movements and to check its dimensions such as retracted length, stroke, etc. The design started by modeling every single part, then the final 3D assembly model was created. In Fig. 8 you can see cut view and front view of 10 stage cylinder. Fig. 9 show axonometric view of 10 stage cylinder in maximum extension. Fig. 5. Sleeves Speeds - 10-stages telescopic cylinder. It was possible to create a chart from the worksheet data to show the telescopic cylinder performance. (a) (b) Fig. 8. (a) 10-stages cylinder; (b) Section view. 40 Table. 5. Diameter and sleeve length of 4- stage cylinder Numbers of stages Diameter Sleeve length [mm] [mm] 1 107 1750 2 126 1750 3 145 1750 4 165 1750 Table. 6. Areas, volumes and speeds of four stage N° of Sleeve Cross Sleeve Volume Sleeve Speed stages section area [m³] [mm/s] [mm²] 1 8992 0.015 935 2 12469 0.021 674 3 16513 0.028 509 Fig. 9. Maximum extension10-stages cylinder. 4 21383 0.037 393 Total 0.161 The 3D ball joint model is created using technical design and data from a company that produces hydraulic cylinders From the space-time chart it was possible to analyze the and components. We have chosen this type of interface to theoretical performance of this 4-stages telescopic cylinder. reduce the problem of misalignment and transversal force that Then it was made a comparison graph between the skip and they can reduce the lifting force and increase the friction the cylinder space-time charts. coefficient t [6 - 9]. It was created a design of a 4-stages telescopic cylinder take into account the effect of friction and functional Tolerancing [10, 11]. It was found that the latter space-time cylinder chart is more similar to the linear skip’s chart. (a) (b) Fig. 10. (a) Ball joint; (b) Ball joint assembled on last stage. (a) (b) Fig. 12. Comparison chart between rope lifting and 4-stages cylinder. Figures below show the design of the 4-stages telescopic cylinder with some details views. In order to find the perfect cylinder features to realize a space-time trend chart as linear as possible, it was chosen a plunger’s diameter of 107 mm, that can lift up to 3000 kg. (c) (d) Fig. 11. (a) ball seat; (b) ring, (c) ball. Using Excel a new space-time chart was obtained considering a cylinder with a fewer number of stages. 41 V. HYDRAULIC DRIVE SYSTEM LAYOUT A hydraulic drive system is a drive or transmission system that uses pressurized hydraulic fluid to power hydraulic machinery. A hydraulic drive system consists of three parts: • Power supply section: a hydraulic pump driven by an electric motor; (a) (b) • Power control section : valves, filters, piping, etc using to guide and control the system; • Drive section : a hydraulic actuator using to drive the machinery. This system is used where the telescopic cylinder piston is returned by the gravity force. With the 4/3-way directional control valve in neutral position (5), pump flow passes though the valve and back to the storage/fluid tank (1) also known as reservoir. The liquid, is generally high density incompressible oil. It is filtered to remove dust or any other unwanted particles and then pumped by the hydraulic pump. The oil filtration unit is also often contained in the power supply section. Impurities can be introduced into the system as a result of mechanical wear, too hot or too cold oil or external environmental influences. For this reason, filters are installed in the hydraulic circuit to remove dirt particles from the hydraulic fluid. Water and gases in the oil are also disruptive (c) factors and special measures must be taken to remove them. Fig. 13. (a) Detail of the top; (b) Detail of a cut view of the top; Valves are devices for controlling the energy flow. (c) 4-stages telescopic cylinder - fully extended. They can control and regulate the flow direction of the hydraulic fluid, the pressure, the flow rate and, consequently, In order to find the perfect cylinder features to realize a the flow velocity. space-time trend chart as linear as possible, it was chosen a With the 4-stages telescopic cylinder, it is possible to have plunger’s diameter of 107 mm, that can lift up to 3000 kg. lower speed at the end of the stroke with a minimum stage Using Excel it was created a comparison space-time chart diameter (d) of 107 mm. The piston surface is: between two different trends: 4 and 10 stages cylinders. The next figure shows a comparison chart between the skip and the (5) other two types of cylinders trends. The cylinder total load capacity is 3000 kg. However to By comparing the above charts is possible to observe that increase the plant safety an higher weight is considered to dynamic motions of 4-stages cylinder are better than a 10- select the correct pump. Considering a safety weight of 4000 stages type because the former has a less accentuated speed kg the max operating pressure is: trend, the line has a reduced slope, and the trend chart is more similar to the skip’s chart. For the above reasons the 4-stages (6) cylinder was selected to be fitted in the hydraulic system while the 10-stage configuration was rejected. Due to the possible oil leakages and other leaks in the system, system operating pressure is increased up to the safety value of 60 bar. The stroke time of the telescopic cylinder is given by the stroke of the cylinder per the cylinder speed (t= 34 m/min): (7) The flow rate is: (8) Q = 504,53 [l/min]. If the pump couples with an asynchronous 4 pole three- phase self-braking electric motor operating at 1450 rpm, the capacity of the pumps is: Fig. 14. 10 Stage cylinder speed; 4 Stage cylinder speed and Skip speed. (9) 42 The choice of the pump is approached by researching [9] Calì, M., Oliveri, S. M., Sequenzia, G. & Fatuzzo, G. Companies producing internal hydraulic gear pump, which is (2017). An effective model for the sliding contact forces in the best option to be fitted in the hydraulic system. a multibody environment. In Advances on Mechanics, Design Engineering and Manufacturing pp. 675-685. Springer, Cham. VI. CONCLUSIONS [10] Capizzi, G., Sciuto, G.L., Napoli, C., Shikler, R. and In the paper was described geometric optimized design of Woźniak, M. (2018). Optimizing the Organic Solar Cell an hydraulic system that would allows a mobile batching plant Manufacturing Process by Means of AFM Measurements to improve the safety, to increase the reliability and to reduce and Neural Networks. Energies, 11(5), pp.1-13. the concrete working process time. In particular, the present [11] Beritelli, F., Capizzi, G., Sciuto, G.L., Napoli, C. and paper outlines the dynamic behavior of a telescopic hydraulic Scaglione, F. (2018). Rainfall Estimation Based on the cylinder in order to replace the current lift system (skip). Intensity of the Received Signal in a LTE/4G Mobile Due to troubleshooting and maintenance issues regarding Terminal by using a Probabilistic Neural Network. IEEE the hydraulic system and difficulties in controlling the Access. Online. DOI: 10.1109/ACCESS.2018.2839699 . cylinder’s retraction speed, a double acting cylinder could be [12] Tran, X. B., Hafizah, N., & Yanada, H. (2012). Modeling an option to solve technical problems. However, even with the of dynamic friction behaviors of hydraulic cylinders. application of this device, there is a need of continue Mechatronics, 22(1), pp. 65-75. maintenance program to make the cylinder operable and safe [13] Calì, M., Oliveri, S.M., Ambu, R. & Fichera, G. (2017). for a long period of time without dangerous sudden failure An Integrated Approach to Characterize the Dynamic [12], in particular way for sealing gaskets, subjected to sliding Behaviour of a Mechanical Chain Tensioner by contact force, infact is extremely important to maintance the Functional Tolerancing. Strojniški vestnik - Journal of optimal operating tolerance standard [13], and contact with the Mechanical Engineering. pp. 245-257. metal surface of the extensions and therefore the seal [14]. [14] Yang, M., Shaoping, W. (2011). Failure Diagnosis of Possible future developments for the present work could be oriented in researching new applications of telescopic Hydraulic Lifting System Based on Multistage Telescopic hydraulic systems to be applied in other concrete plants with Cylinder. In Fluid Power and Mechatronics (FPM), 2011 different technical requirements. International Conference IEEE. pp. 828-834. [15] Calì, M., Zanetti, E. M., Oliveri, S. M., Asero, R., REFERENCES Ciaramella, S., Martorelli, M., & Bignardi, C. (2018). [1] Crossman, J., Lauer, N., & Barter, S. D. (2005). U.S. Influence of thread shape and inclination on the Patent No. 6,913,040. Washington, DC: U.S. Patent and biomechanical behaviour of plateau implant systems. Trademark Office. Dental Materials, 34(3), pp. 460-469. [2] Fangmann, T., & Gröger, D. (2002). U.S. Patent No. [16] Pagliarulo, V., Farroni, F., Ferraro, P., Lanzotti, A., 6,475,380. Washington, DC: U.S. Patent and Trademark Martorelli, M., Memmolo, P., Domenico, S. & Timpone, Office. F. (2017). Combining ESPI with laser scanning for 3D [3] Morikawa, R., Kajita, Y., & Sugiyama, G. (1992). U.S. characterization of racing tyres sections. Optics and Patent No. 5,161,373. Washington, DC: U.S. Patent and Lasers in Engineering,104, pp. 72-73. Trademark Office. [17] Sciuto, G.L., Capizzi, G., Napoli, C., Shikler, R., Połap, [4] Ambu, R., Bertetto, M. A., Falchi, C. (2014). Design of a D. and Woźniak, M. (2018). Exploiting OSC Models by prototype system operant in lunar environment. Strojniški Using Neural Networks with an Innovative Pruning vestnik-Journal of Mechanical Engineering, 60(10), pp. Algorithm. In International Conference on Artificial 629-637. Intelligence and Soft Computing, pp. 711-722. Springer. [5] Totten, G. E. (2011). Handbook of hydraulic fluid technology. CRC Press. [6] Deligiannis, V, & Manesis, S. (2008). Concrete batching and mixing plants: A new modeling and control approach based on global automata. Automation in Construction, 17(4), pp. 368-376. [7] Damaševičius, R., Napoli, C., Sidekerskienė, T. and Woźniak, M. (2017). IMF mode demixing in EMD for jitter analysis. Journal of Computational Science, 22, pp.240-252. [8] Gamez-Montero, P. J., Salazar, E., Castilla, R., Freire, J., Khamashta, M., & Codina, E. (2009). Misalignment effects on the load capacity of a hydraulic cylinder. International Journal of Mechanical Sciences, 51(2), pp. 105-113. 43